We're always on hand to help you with a flat tyre, but if you fancy being a bit more independent, here’s how to have a go yourself.
If you've got a new car, it's quite likely you'll have a tyre puncture repair kit2020欧冠预选赛赛程时间 in the car rather than a spare wheel. If this is the case, familiarise yourself with your kit, so you’ll know what to do if you do get a puncture.
Staying safe when you change a tyre
2020欧冠预选赛赛程时间If your tyre bursts while you're driving, keep a firm grip on the steering and slow down gently, avoiding harsh braking. Keep driving, slowly, and find a safe place to stop.
- Don’t change your wheel on the hard shoulder of a motorway or at the side of a road. Turn off or pull over well away from the traffic and call us for help on 0800 88 77 66.
- Don’t change your wheel on soft, loose or uneven ground.
- Don’t change your wheel with passengers inside the vehicle. Move everyone to a safe place that’s well away from the vehicle and road.
- Don’t work under your vehicle while it's raised on a jack.
- Don’t use the jack anywhere other than at the correct jacking points &ndash you’ll find these listed in your handbook. Attaching the jack in the wrong place can cause damage to your vehicle and could result in it collapsing
Before you start changing or repairing your tyre, make sure you’ve read your vehicle’s handbook. If our advice is different to what’s in it, always follow your handbook.
What equipment do you need to change a tyre?
Make sure you have the right kit in your car to change a tyre. It's also a good idea to perform regular checks on your tyres to make sure they're in a safe and legal condition.
Here's what you need to change a tyre:
- Your handbook, which shows you where to attach the jack.
- Make sure your spare tyre is in good condition; it's common for drivers to find an unusable tyre in their boot, with no alternative. Make sure it’s got enough tread and is properly inflated.
- Your vehicle jack.
- A wheel wrench with extension bar and locking wheel-nut adaptor (if fitted).
- At least one wheel chock – this is something to stop your car from rolling when it’s up on the jack.
- Gloves – there’s a good chance your wheel/tyre will be dirty.
- Something to kneel on, like an old towel – the ground will be dirty too.
- A sharp knife or cutters to remove any cable ties used to hold your wheel trims in place.
- A torch.
- A reflective jacket and strong, sensible shoes for your own safety.
Before you lift your vehicle
Before you use your car jack to raise your vehicle, there are a few things that you should do first:
- Switch off your engine and turn on your hazard lights.
- Apply the handbrake and engage first gear (or 'P' if you’re driving an automatic).
- Put your chock under the wheel diagonally opposite the one you’re replacing.
- Remove your spare wheel from the boot well/carrier. If the carrier is under your vehicle, it might be a bit rusty and difficult to move.
- Lay your spare on the ground. Choose a spot that will be convenient for fitting.
- Remove your wheel trim (if fitted) – you may have to cut cable ties and/or lever the trim off.
How to use a car jack:
- Place the jack in the lifting point closest to the wheel you’re changing.
- To find the proper place to position the jack, consult your owner’s manual.
- Make sure the jack head engages properly (as shown in your handbook) and extend the jack until it just starts to lift the vehicle on its springs. Don't lift your vehicle any further yet.
- Loosen the wheel nuts (anticlockwise) using the vehicle's wheel wrench and locking wheel-nut adapter if needed. There might be protective covers over the locking wheel nuts.
- Keep your back straight and body weight evenly distributed on both feet. Apply effort downwards in a controlled way, so that when the nut finally 'gives' you won't lose your balance.
- Raise the jack until the wheel is just off the ground.
- Remove the loose wheel nuts while keeping the wheel in position with your knee or foot.
- Leave the top one until last, so you can use both hands to lift the wheel away from the hub.
How to fit a spare tyre
If your spare wheel is a temporary-use 'skinny' spare, make sure you check any restrictions on using it. Usually, you can only travel up to 50mph on a skinny spare, and you’ll need to replace it with a normal tyre as soon as you can.
- Secure the wheel by loosely refitting the top wheel nut first.
- Tighten the remaining wheel nuts by hand, firstly in stages and in a diagonal sequence.
- Don't oil the wheel nuts before refitting them, since this will make them more likely to work loose.
- Lower the jack carefully until the wheel just touches the ground and won’t turn.
- Now tighten the wheel nuts fully with the wheel wrench, again in a diagonal sequence.
- Put the damaged wheel in the boot well or carrier.
What to do after you fit a spare tyre
As soon as you can get to a dealer or a garage, make sure you:
- Have the pressure in the spare tyre checked.
- Get your wheel nuts tightened properly.
- Replace or repair the damaged tyre.